The Gap filler plank is designed to span small openings in the Ringlock platform or between bays. They can also be used to overalp on circular scaffolds and perform the angular connection. They are fized with a plastic plug that is provided with them. They are available in two widths: 0.32m and 0.19m and un 3 different lengths: 1.00m, 1.50m and 2.00m.

Art.-No. 468

Truss ledgers have the same function as the normal ledgers: They are used as horizontals to connect standards, to transfer loads from platforms into standards and for making side protection of the scaffold. But due to reinforced design, they are able to transfer higher loads than normal ledgers. Double ledgers are available in lengths 1.40m, 1.57m, 2.07m, 2.57m, 3.07m.

Art.-No. 527

The bracket is used to create an extended platform outside the scaffold and to add a "cantilever" to the construction. Brackets are available in lengths 0.39m, 0.73m and 1.09m.

Art.-No. 543

Ledgers are used as horizontals to connect standards and to transfer loads from platforms into standards. Ledgers are also used for making side protection of the scaffold. Ledgers are available in lengths 0.15m, 0.39m, 0.73m, 1.04m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m, 3.07m.

Art.-No. 549

Infill planks with 19cm are designed to fill any unwanted gaps between planks or bays providing a continuous working platform. They are available in the sizes of the most common bays: 0.65m, 0,88m, 1.065m, 1.57m, 2.13m, 2.43m, 3.05m.

Art.-No. 556

Steel plans are used to create a working platform in a scaffold. They are placed directly onto the ledgers and secured with the integrated lift-out guard. Steel planks are available with two widths 0.19m and 0.32m and in lengths 0.73m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m, 3.07m.

Art.-No. 557

Steel planksare used to create a working platform in a scaffold. They are placed directly onto the ledgers and secured with the integrated lift-out guard. Steel planks are available with two widths 0.19m and 0.32m and in lengths 0.73m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m, 3.07m.

Art.-No. 559

Steel toe boards are mounted on working platforms to prevent material from falling down. These Toeboards are galvanized and not yellow.

Art.-No. 561

Bay braces are essential to increase the vertical stiffness of the scaffold! For stabilizing the outer plane of the scaffold, parallel and perpendicular to the facade, vertical braces are used. Vertical braces are placed in at least every 5th bay on every lift and in every end bay perpendicular to the facade. Diagonals are available for 1.00m, 1.50m and 2.0m heights, and bay lengths of 0.73m, 1.09m, 1.40m, 1.57m, 2.07m, 2.57m, 3.07m.

Art.-No. 574

Allows advancing guard rail protection during erection, modification and dismantling of the scaffold.

Art.-No. 636

The wall tie tube is a scaffold tube with pin, designed to keep the standards in the vertical position without buckling.

Art.-No. 689

The Gap Filler Plates are designed to fill any unwanted gaps between planks or bays creating continuous platforms and can easily be installed in the same method as the infill planks and can be secured to the main planks.

Art.-No. 690

The stairs are used to provide access to the various deck levels within the scaffold. The aluminum platform stairs are suitable for 2.00 kN/m² (EN12811: class 3). Alu-stairways are available in lengths of 2.57m, 3.07m.

Art.-No. 718

The inner guardrail 1m is used to shield the inner side of a 1m staircase.

Art.-No. 719

The Girder transom enables a standard to be installed along the length of a bay when secured to two standards.

Art.-No. 730

Art.-No. 319022075

The Ladder Hatch Plank acts as a lightweight, extra wide Scaffold Plank which incorporates a hatch.

Art.-No. 319023075

The Ladder Hatch Plank acts as a lightweight, extra wide Scaffold Plank which incorporates a hatch and a ladder.

Art.-No. 310067004

The Access barriers are designed to be used as a guardrail at the top and bottom of the Aluminum 4 leg Platform Stairs and can also be used to provide barriers around gaps in platforms for ladder access.

Art.-No. 308132505

The Gap Filler Plank is designed to span small openings in the Ringlock platform or between bays and can easily be installed over a gap and secured to the Steel Plank to prevent further movement. Available in two different widths 320mm and 190mm.

Art.-No. 333040005

The Ballast weight holder secures to the Standard to prevent overturning when used with Ballast weights.